PIC18F13K50-I/P【PDF 8/285 页】IC PIC MCU FLASH 4KX16 20-PDIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3873

4页 5页 6页 7页 [8页]9页 10页 11页 12页

2010 Microchip Technology Inc.

Preliminary

DS41350E-page 105

PIC18F/LF1XK50

11.0

TIMER1 MODULE

The Timer1 timer/counter module incorporates the

following features:

Software selectable operation as a 16-bit timer or

counter

Readable and writable 8-bit registers (TMR1H

and TMR1L)

Selectable internal or external clock source and

Timer1 oscillator options

Interrupt-on-overflow

Reset on CCP Special Event Trigger

Device clock status flag (T1RUN)

A simplified block diagram of the Timer1 module is

shown in Figure 11-1. A block diagram of the module’s

operation in Read/Write mode is shown in Figure 11-2.

The module incorporates its own low-power oscillator

to provide an additional clocking option. The Timer1

oscillator can also be used as a low-power clock source

for the microcontroller in power-managed operation.

Timer1 can also be used to provide Real-Time Clock

(RTC) functionality to applications with only a minimal

addition of external components and code overhead.

Timer1 is controlled through the T1CON Control

Oscillator Enable bit (T1OSCEN). Timer1 can be

enabled or disabled by setting or clearing control bit,

TMR1ON of the T1CON register.

REGISTER 11-1:

T1CON: TIMER1 CONTROL REGISTER

R/W-0

R-0

R/W-0

RD16

T1RUN

T1CKPS1

T1CKPS0

T1OSCEN

T1SYNC

TMR1CS

TMR1ON

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

RD16: 16-bit Read/Write Mode Enable bit

= Enables register read/write of TImer1 in one 16-bit operation

= Enables register read/write of Timer1 in two 8-bit operations

bit 6

T1RUN: Timer1 System Clock Status bit

= Main system clock is derived from Timer1 oscillator

= Main system clock is derived from another source

bit 5-4

T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits

= 1:8 Prescale value

= 1:4 Prescale value

= 1:2 Prescale value

= 1:1 Prescale value

bit 3

T1OSCEN: Timer1 Oscillator Enable bit

= Timer1 oscillator is enabled

= Timer1 oscillator is shut off

The oscillator inverter and feedback resistor are turned off to eliminate power drain.

bit 2

T1SYNC: Timer1 External Clock Input Synchronization Select bit

When TMR1CS = 1:

= Do not synchronize external clock input

= Synchronize external clock input

When TMR1CS = 0:

This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.

bit 1

TMR1CS: Timer1 Clock Source Select bit

= External clock from the T13CKI pin (on the rising edge)

= Internal clock (FOSC/4)

bit 0

TMR1ON: Timer1 On bit

= Enables Timer1

= Stops Timer1

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式